- TF-A - lists.trustedfirmware.org

SP manifest: avoid manual updates to "entrypoint-offset"

by Varun Wadekar

Hello, We (Nico/Raghu) have been implementing SEL0 partitions for Tegra platforms and recently hit an issue, where the "entrypoint-offset" field of the SP manifest [1] cannot cope with increasing manifest blobs. The way the SP manifest is created today, the "entrypoint-offset" field is set to a value *statically* by the implementer. Down the line if the manifest grows past the value written in the "entrypoint-offset", we must manually update it. This needs to be fixed. We believe there is an opportunity to upgrade the sptool to handle this situation during SP package creation, where sptool calculates the manifest size and bumps the "entrypoint-offset" past the end of the manifest. There are other ways of patching the SP manifest at runtime, but they seem sub-optimal. Please let me know if there are other ideas to solve this problem. I will post a patch to update the sptool shortly but wanted to get the ball rolling. Cheers. [1] 14. FF-A manifest binding to device tree - Trusted Firmware-A documentation<https://trustedfirmware-a.readthedocs.io/en/latest/components/ffa-manifest-…>

4 years, 4 months

1
0
0 0

Test Post

by Arjun Khare

Test (sorry for the noise)

4 years, 4 months

1
0
0 0

Re: [TF-A] Support for Kinibi in ATF/SPMD - linear ID

by Achin Gupta

Hi Francois, The blobs are passed in memory only when the primary core boots. The linear id is required when both primaries and secondaries boot. Secondly, the linear id is used to reference per-cpu structures in memory during very early initialisation. Putting the linear id in a memory structure would either require a per-cpu structure (chicken and egg) or a read-only global structure (to avoid complicated locks with the MMU turned off). It seems to me that the linear id should be passed in an unused register specified by the partition manifest. Passing it in the blob list seems a bit counter intuitive to me but happy to understand your thoughts better. cheers, Achin ________________________________ From: TF-A <tf-a-bounces(a)lists.trustedfirmware.org> on behalf of François Ozog via TF-A <tf-a(a)lists.trustedfirmware.org> Sent: 14 June 2021 16:29 To: Lukas Hanel <lukas.hanel(a)trustonic.com> Cc: tf-a(a)lists.trustedfirmware.org <tf-a(a)lists.trustedfirmware.org> Subject: Re: [TF-A] Support for Kinibi in ATF/SPMD - linear ID This looks like a good candidate for the bloblist discussion we have on other mail thread. Why not aggregating "topology" metadata in a block rather than passing "random" information elements in registers? On Thu, 10 Jun 2021 at 13:57, Lukas Hanel via TF-A <tf-a(a)lists.trustedfirmware.org<mailto:tf-a@lists.trustedfirmware.org>> wrote: Hi, in this PR, I propose a first change to the SPMD to better support Kinibi, the TEE from Trustonic. https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/10235 The idea here is to pass the core linear id in the x3 register in the boot of secondary cores. In the past, the Kinibi SPD was not public and so some requirements to TF-A were not visible to the wider community. For Kinibi, one binary should run on a multitude of platforms. For that reason, many platform-specific settings are shared by TF-A with Kinibi: at boot, in registers and in a boot datastructure, and at runtime. In the line of work of making Kinibi compatible with FFA APIs, I moved some bits from the Kinibi SPD to the SPMD. Instead of sharing such patches only with our customers, we would like to upstream the patches to the generic code. For this particular patch, it is really simple and changes the interface SPMD-to-SPMC in a somewhat adhoc manner. There is some discussion within ARM to standardize such behavior and to propose configuration options, i.e. within a manifest. That way, you could change what register the linear id, if at all, should be transferred in. A first tour of the CI showed that there seem to be no consequences to hafnium and optee. I guess, question to the mailing list, is there something that this patch breaks? Greetings, Lukas Trustonic SAS - 535 route de Lucioles, Les Aqueducs Batiment 2, Sophia Antipolis 06560 Valbonne, France – SAS au capital de 3 038 000€ - RCS Grasse – SIRET 480 011 998 00055 - TVA intracommunautaire : FR02 480 011 998 -- TF-A mailing list TF-A(a)lists.trustedfirmware.org<mailto:TF-A@lists.trustedfirmware.org> https://lists.trustedfirmware.org/mailman/listinfo/tf-a -- [https://drive.google.com/a/linaro.org/uc?id=0BxTAygkus3RgQVhuNHMwUi1mYWc&ex…] François-Frédéric Ozog | Director Linaro Edge & Fog Computing Group T: +33.67221.6485 francois.ozog(a)linaro.org<mailto:francois.ozog@linaro.org> | Skype: ffozog

4 years, 4 months

2
1
0 0

Re: [TF-A] Support for Kinibi in ATF/SPMD - linear ID

by François Ozog

This looks like a good candidate for the bloblist discussion we have on other mail thread. Why not aggregating "topology" metadata in a block rather than passing "random" information elements in registers? On Thu, 10 Jun 2021 at 13:57, Lukas Hanel via TF-A < tf-a(a)lists.trustedfirmware.org> wrote: > Hi, > > in this PR, I propose a first change to the SPMD to better support Kinibi, > the TEE from Trustonic. > https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/10235 > > The idea here is to pass the core linear id in the x3 register in the boot > of secondary cores. > > In the past, the Kinibi SPD was not public and so some requirements to > TF-A were not visible to the wider community. > For Kinibi, one binary should run on a multitude of platforms. > For that reason, many platform-specific settings are shared by TF-A with > Kinibi: at boot, in registers and in a boot datastructure, and at runtime. > > In the line of work of making Kinibi compatible with FFA APIs, I moved > some bits from the Kinibi SPD to the SPMD. > Instead of sharing such patches only with our customers, we would like to > upstream the patches to the generic code. > > For this particular patch, it is really simple and changes the interface > SPMD-to-SPMC in a somewhat adhoc manner. > There is some discussion within ARM to standardize such behavior and to > propose configuration options, i.e. within a manifest. > That way, you could change what register the linear id, if at all, should > be transferred in. > > A first tour of the CI showed that there seem to be no consequences to > hafnium and optee. > I guess, question to the mailing list, is there something that this patch > breaks? > > Greetings, > Lukas > > > Trustonic SAS - 535 route de Lucioles, Les Aqueducs Batiment 2, Sophia > Antipolis 06560 Valbonne, France – SAS au capital de 3 038 000€ - RCS > Grasse – SIRET 480 011 998 00055 - TVA intracommunautaire : FR02 480 011 998 > -- > TF-A mailing list > TF-A(a)lists.trustedfirmware.org > https://lists.trustedfirmware.org/mailman/listinfo/tf-a > -- François-Frédéric Ozog | *Director Linaro Edge & Fog Computing Group* T: +33.67221.6485 francois.ozog(a)linaro.org | Skype: ffozog

4 years, 4 months

1
0
0 0

Support for Kinibi in ATF/SPMD - linear ID

by Lukas Hanel

Hi, in this PR, I propose a first change to the SPMD to better support Kinibi, the TEE from Trustonic. https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/10235 The idea here is to pass the core linear id in the x3 register in the boot of secondary cores. In the past, the Kinibi SPD was not public and so some requirements to TF-A were not visible to the wider community. For Kinibi, one binary should run on a multitude of platforms. For that reason, many platform-specific settings are shared by TF-A with Kinibi: at boot, in registers and in a boot datastructure, and at runtime. In the line of work of making Kinibi compatible with FFA APIs, I moved some bits from the Kinibi SPD to the SPMD. Instead of sharing such patches only with our customers, we would like to upstream the patches to the generic code. For this particular patch, it is really simple and changes the interface SPMD-to-SPMC in a somewhat adhoc manner. There is some discussion within ARM to standardize such behavior and to propose configuration options, i.e. within a manifest. That way, you could change what register the linear id, if at all, should be transferred in. A first tour of the CI showed that there seem to be no consequences to hafnium and optee. I guess, question to the mailing list, is there something that this patch breaks? Greetings, Lukas Trustonic SAS - 535 route de Lucioles, Les Aqueducs Batiment 2, Sophia Antipolis 06560 Valbonne, France - SAS au capital de 3 038 000EUR - RCS Grasse - SIRET 480 011 998 00055 - TVA intracommunautaire : FR02 480 011 998

4 years, 4 months

1
0
0 0

Re: [TF-A] please fix incomplete distclean Makefile target

by Manish Pandey2

Hi, Can you try below steps, try with fresh pull? 1. Login with your github account on https://review.trustedfirmware.org/admin/repos/TF-A%2Ftrusted-firmware-a 2. git clone "ssh://<user>@review.trustedfirmware.org:29418/TF-A/trusted-firmware-a 3. git push <remote-name> HEAD:refs/for/integration 4. While pushing if it complains about git hooks, run scp -p -P 29418 <user>@review.trustedfirmware.org:hooks/commit-msg "trusted-firmware-a/.git/hooks/" and amend your commit (it will give you this hint) ________________________________ From: TF-A <tf-a-bounces(a)lists.trustedfirmware.org> on behalf of Nicolas Boulenguez via TF-A <tf-a(a)lists.trustedfirmware.org> Sent: 03 April 2021 13:02 To: raghu.ncstate(a)icloud.com <raghu.ncstate(a)icloud.com> Cc: tf-a(a)lists.trustedfirmware.org <tf-a(a)lists.trustedfirmware.org>; 'Benjamin Copeland' <ben.copeland(a)linaro.org> Subject: Re: [TF-A] please fix incomplete distclean Makefile target raghu.ncstate(a)icloud.com: > Are you pushing ssh://<username>@review.trustedfirmware.org:29418/TF-A/trusted-firmware-a HEAD:refs/for/integration? > Note that 29418 port. That tripped me up initially. It is not clear from your earlier emails where you cloned from(review.trustedfirmware.org or git.trustedfirmware.org). [α] links to [β] which recommends # git clone "https://review.trustedfirmware.org/TF-A/trusted-firmware-a" I had an existing repository (most contributors probably do) and used 'git add remote' and 'git fetch' instead. [α] recommends # git push <remote-name> HEAD:refs/for/integration%<topic-branch> As expected, the host requires a password. # git push ssh://<user>@review.trustedfirmware.org:29418/TF-A/trusted-firmware-a HEAD:refs/for/integration? -> fatal: invalid refspec 'HEAD:refs/for/integration?' Anyhow, the host would require an SSH key. [α] https://developer.trustedfirmware.org/w/tf_a/gerrit-getting-started/ [β] https://review.trustedfirmware.org/admin/repos/TF-A%2Ftrusted-firmware-a -- TF-A mailing list TF-A(a)lists.trustedfirmware.org https://lists.trustedfirmware.org/mailman/listinfo/tf-a

4 years, 4 months

2
1
0 0

Re: [TF-A] issue with vsnprintf() and unsigned_num_print()

by Varun Wadekar

HI Hiren, Can you please add more color to “even if I provide large enough string to hold the number, it does not print it”? Are you saying that the library prints a partial value? If the calculation is off by 1, I assume, the library should at least print a partial value. -Varun From: TF-A <tf-a-bounces(a)lists.trustedfirmware.org> On Behalf Of Hiren Mehta via TF-A Sent: Saturday, May 29, 2021 9:41 AM To: tf-a(a)lists.trustedfirmware.org Subject: [TF-A] issue with vsnprintf() and unsigned_num_print() External email: Use caution opening links or attachments Hi All, We are using the snprintf() (which uses vsnprintf() and unsigned_num_print()) from libc of ATF version 2.4 and running into an issue for printing a number into a string where even if I provide large enough string to hold the number, it does not print it. I don't see that issue with it when I try to print a string using the same snprintf(). I understand that, as per the documentation use of snprintf is "banned or discouraged". But for the use case, that we are using for, it is safe enough to use it assuming that it does it what it is supposed to do. I am not sure if this is a known bug or what, but upon a further inspection, I found that there seems be a small bug in the unsigned_num_print() for one of the 'if' condition given below which is causing the issue in terms of calculating the available space in the string. if (*chars_printed < n) { .... do the prinring.... } I believe it is supposed to be if (*chars_printed <= n) { ----------------->> Notice '<=' instead of '<' } Any comment on whether this is on purpose or really a small bug? The calling routine (vsnprintf) is already reducing 'n' by 1 for the terminating null character. Thank you very much for your support. -hiren

4 years, 5 months

2
2
0 0

Re: [TF-A] TF-A Tech Forum Agenda @ Thr 3rd June 2021 16:00-1700 BST

by François Ozog

Hi food for thought for tomorrow's call: Passing information on what is plugged into the DIMM slots may not be as straightforward as it sounds. You can plug pure DRAM, NVDIMMs or pure flash (from Diablo technologies, acquired by RAMBus in 2019). The pure flash is a module where there is a few MB as bounce buffers to flash located on the DIMM itself. The largest element was 1TB on a single DIMM. So passing a C structure that details the size of the DIMM fails to fully describe NVDIMM and Flash on DIMM. Those two things required complex Passing a DT fragment that describes the plugged module is generic and can describe both the bounce buffers and the registers needed to access the flash on DIMM. In the future you may find associative memory or whatever AI based modules. Bottom line, using DT fragment to describe memory is flexible for the three existing cases and future proof. The document shows that for a 2 DIMM representation and associated SPDs, the additional cost is 88 bytes. 32 are fixed cost, 56 are somewhat name size dependent and some related to FDT format. There is no need for a full libfdt to actually produce that serialized data on a hob. So in my view, the benefit of having an alignment, version and evolution proof structure that comes with DT fragment by far exceeds the cost of a few bytes saved, even in the context of SRAM size. Cheers FF On Wed, 2 Jun 2021 at 17:33, Joanna Farley via TF-A < tf-a(a)lists.trustedfirmware.org> wrote: > Hi All, > > > > The next TF-A Tech Forum is scheduled for Thu 3rd June 2021 16:00 – 17:00 > (BST). > > > > Agenda: > > - Discussion Session: Static and Dynamic Information Handling in TF-A > (Session 2) > - Lead by Manish Pandy and Madhukar Pappireddy > - On tech forum this week, we would like to continue discussions on > HOB list design. > - The topics which we would like to cover is > 1. Evaluate different proposals of passing information through > boot phases. > 2. If we don't get an agreement on one solution fit for all then > we would try to get consensus for Infra segment platform(to solve original > problem mentioned by Harb) > 3. Try to get an agreement on size of tags and how "hybrid and > tag only" HOB list can co-exist together? > > > > > > Thanks > > > > Joanna > > > > > *You have been invited to the following event.* TF-A Tech Forum > > *more details » > <https://www.google.com/calendar/event?action=VIEW&eid=NWlub3Ewdm1tMmk1cTJrM…>* > > > > We run an open technical forum call for anyone to participate and it is > not restricted to Trusted Firmware project members. It will operate under > the guidance of the TF TSC. > > > > Feel free to forward this invite to colleagues. Invites are via the TF-A > mailing list and also published on the Trusted Firmware website. Details > are here: https://www.trustedfirmware.org/meetings/tf-a-technical-forum/ > <https://www.google.com/url?q=https%3A%2F%2Fwww.trustedfirmware.org%2Fmeetin…> > > > > Trusted Firmware is inviting you to a scheduled Zoom meeting. > > > > Join Zoom Meeting > > https://zoom.us/j/9159704974 > <https://www.google.com/url?q=https%3A%2F%2Fzoom.us%2Fj%2F9159704974&sa=D&us…> > > > > Meeting ID: 915 970 4974 > > > > One tap mobile > > +16465588656,,9159704974# US (New York) > > +16699009128,,9159704974# US (San Jose) > > > > Dial by your location > > +1 646 558 8656 US (New York) > > When > > Every 2 weeks from 16:00 to 17:00 on Thursday United Kingdom Time > > Calendar > > tf-a(a)lists.trustedfirmware.org > > Who > > • > > Bill Fletcher- creator > > • > > tf-a(a)lists.trustedfirmware.org > > +1 669 900 9128 US (San Jose) > > 877 853 5247 US Toll-free > > 888 788 0099 US Toll-free > > Meeting ID: 915 970 4974 > > Find your local number: https://zoom.us/u/ad27hc6t7h > <https://www.google.com/url?q=https%3A%2F%2Fzoom.us%2Fu%2Fad27hc6t7h&sa=D&us…> > > > > > Going (tf-a(a)lists.trustedfirmware.org)? All events in this series: * > Yes > <https://www.google.com/calendar/event?action=RESPOND&eid=NWlub3Ewdm1tMmk1cT…>** > - **Maybe > <https://www.google.com/calendar/event?action=RESPOND&eid=NWlub3Ewdm1tMmk1cT…>** > - **No > <https://www.google.com/calendar/event?action=RESPOND&eid=NWlub3Ewdm1tMmk1cT…>* > more options » > <https://www.google.com/calendar/event?action=VIEW&eid=NWlub3Ewdm1tMmk1cTJrM…> > > Invitation from Google Calendar <https://www.google.com/calendar/> > > You are receiving this courtesy email at the account > tf-a(a)lists.trustedfirmware.org because you are an attendee of this event. > > To stop receiving future updates for this event, decline this event. > Alternatively, you can sign up for a Google Account at > https://www.google.com/calendar/ and control your notification settings > for your entire calendar. > > Forwarding this invitation could allow any recipient to send a response to > the organiser and be added to the guest list, invite others regardless of > their own invitation status or to modify your RSVP. Learn more > <https://support.google.com/calendar/answer/37135#forwarding>. > > > -- > TF-A mailing list > TF-A(a)lists.trustedfirmware.org > https://lists.trustedfirmware.org/mailman/listinfo/tf-a > -- François-Frédéric Ozog | *Director Linaro Edge & Fog Computing Group* T: +33.67221.6485 francois.ozog(a)linaro.org | Skype: ffozog

4 years, 5 months

1
0
0 0

TF-A Tech Forum Agenda @ Thr 3rd June 2021 16:00-1700 BST

by Joanna Farley

Hi All, The next TF-A Tech Forum is scheduled for Thu 3rd June 2021 16:00 – 17:00 (BST). Agenda: * Discussion Session: Static and Dynamic Information Handling in TF-A (Session 2) * Lead by Manish Pandy and Madhukar Pappireddy * On tech forum this week, we would like to continue discussions on HOB list design. * The topics which we would like to cover is * Evaluate different proposals of passing information through boot phases. * If we don't get an agreement on one solution fit for all then we would try to get consensus for Infra segment platform(to solve original problem mentioned by Harb) * Try to get an agreement on size of tags and how "hybrid and tag only" HOB list can co-exist together? Thanks Joanna You have been invited to the following event. TF-A Tech Forum more details »<https://www.google.com/calendar/event?action=VIEW&eid=NWlub3Ewdm1tMmk1cTJrM…> We run an open technical forum call for anyone to participate and it is not restricted to Trusted Firmware project members. It will operate under the guidance of the TF TSC. Feel free to forward this invite to colleagues. Invites are via the TF-A mailing list and also published on the Trusted Firmware website. Details are here: https://www.trustedfirmware.org/meetings/tf-a-technical-forum/<https://www.google.com/url?q=https%3A%2F%2Fwww.trustedfirmware.org%2Fmeetin…> Trusted Firmware is inviting you to a scheduled Zoom meeting. Join Zoom Meeting https://zoom.us/j/9159704974<https://www.google.com/url?q=https%3A%2F%2Fzoom.us%2Fj%2F9159704974&sa=D&us…> Meeting ID: 915 970 4974 One tap mobile +16465588656,,9159704974# US (New York) +16699009128,,9159704974# US (San Jose) Dial by your location +1 646 558 8656 US (New York) When Every 2 weeks from 16:00 to 17:00 on Thursday United Kingdom Time Calendar tf-a(a)lists.trustedfirmware.org Who • Bill Fletcher- creator • tf-a(a)lists.trustedfirmware.org +1 669 900 9128 US (San Jose) 877 853 5247 US Toll-free 888 788 0099 US Toll-free Meeting ID: 915 970 4974 Find your local number: https://zoom.us/u/ad27hc6t7h<https://www.google.com/url?q=https%3A%2F%2Fzoom.us%2Fu%2Fad27hc6t7h&sa=D&us…> Going (tf-a(a)lists.trustedfirmware.org)? All events in this series: Yes<https://www.google.com/calendar/event?action=RESPOND&eid=NWlub3Ewdm1tMmk1cT…> - Maybe<https://www.google.com/calendar/event?action=RESPOND&eid=NWlub3Ewdm1tMmk1cT…> - No<https://www.google.com/calendar/event?action=RESPOND&eid=NWlub3Ewdm1tMmk1cT…> more options »<https://www.google.com/calendar/event?action=VIEW&eid=NWlub3Ewdm1tMmk1cTJrM…> Invitation from Google Calendar<https://www.google.com/calendar/> You are receiving this courtesy email at the account tf-a(a)lists.trustedfirmware.org because you are an attendee of this event. To stop receiving future updates for this event, decline this event. Alternatively, you can sign up for a Google Account at https://www.google.com/calendar/ and control your notification settings for your entire calendar. Forwarding this invitation could allow any recipient to send a response to the organiser and be added to the guest list, invite others regardless of their own invitation status or to modify your RSVP. Learn more<https://support.google.com/calendar/answer/37135#forwarding>.

4 years, 5 months

1
0
0 0

Re: [TF-A] Linux kernel set the hypervisor vector table through ATF

by Marc Zyngier

On Tue, 01 Jun 2021 14:34:05 +0100, Dongjiu Geng <gengdongjiu1(a)gmail.com> wrote: > > Marc Zyngier <maz(a)kernel.org> 于2021年6月1日周二下午6:09写道： > > > > On Tue, 01 Jun 2021 10:53:49 +0100, > > Dongjiu Geng <gengdongjiu1(a)gmail.com> wrote: > > > > > > Mark Rutland <mark.rutland(a)arm.com> 于2021年6月1日周二下午5:19写道： > > > > > > > > On Fri, May 28, 2021 at 05:26:51PM +0800, Dongjiu Geng wrote: > > > > > Hi All, > > > > > when Linux kernel boot from EL1, there is no method to let > > > > > kernel to enter EL2 to enable hypervisor. so I want to add an SMC > > > > > interface between kernel and EL3 ATF to let kernel can set the > > > > > hypervisor vector table, then can enter EL2 to enable hypervisor, as > > > > > shown in [1]. > > > > > Do you agree? Otherwise there is no method to enter EL2 hypervisor > > > > > when kernel boot from EL1, because the hypervisor vector > > > > > table(vbar_el2) is unknown. > > > > > > > > The kernel already supported being booted at EL2, where it will install > > > > itself as the hypervisor (and will drop to EL1 if required). EL2 is the > > > > preferred boot mode, as we document in: > > > > > > > > https://www.kernel.org/doc/html/latest/arm64/booting.html > > > > > > > > ... where we say: > > > > > > > > | The CPU must be in either EL2 (RECOMMENDED in order to have access to > > > > | the virtualisation extensions) or non-secure EL1. > > > > > > > > We *strongly* prefer this over adding new ABIs to transition from EL1 to > > > > EL2. Please boot the kernel at EL2 if you want to use KVM. > > > > > > Thanks for the answer. > > > If use KVM, it should boot from EL2. But if the hypervisor is not > > > KVM, such as Jailhouse hypervisor and some Chip manufacturer boot the > > > host kernel from EL1(not follow above rule), it seems there is not way > > > to enter the Jailhouse hypervisor. > > > > We only deal with two cases: > > - either the kernel uses its own, built-in hypervisor: it boots at > > EL2, and installs itself. > > > > - or there is a pre-existing hypervisor, and the kernel boots at EL1. > > > > In the past, Jailhouse used the exact same entry points as KVM. What > > has changed? > > Jailhouse use the __hyp_stub_vectors vector table[1] in linux > kernel arch/arm64/kernel/hyp-stub.S to re-set his own's hypervisor > vector table, but if linux kernel is boot from EL1，it can not use the > entry points(__hyp_stub_vectors). I agree Linux kernel is recommended > boot from EL2, but some custer's boards not follow this rule. So Jailhouse doesn't have this problem when used as intended. > > [1]: > ENTRY(__hyp_stub_vectors) > ventry el2_sync_invalid // Synchronous EL2t > ventry el2_irq_invalid // IRQ EL2t > ventry el2_fiq_invalid // FIQ EL2t > ventry el2_error_invalid // Error EL2t > > ventry el2_sync_invalid // Synchronous EL2h > ventry el2_irq_invalid // IRQ EL2h > ventry el2_fiq_invalid // FIQ EL2h > ventry el2_error_invalid // Error EL2h > > ventry el1_sync // Synchronous 64-bit EL1 > ventry el1_irq_invalid // IRQ 64-bit EL1 > ventry el1_fiq_invalid // FIQ 64-bit EL1 > ventry el1_error_invalid // Error 64-bit EL1 > > ventry el1_sync_invalid // Synchronous 32-bit EL1 > ventry el1_irq_invalid // IRQ 32-bit EL1 > ventry el1_fiq_invalid // FIQ 32-bit EL1 > ventry el1_error_invalid // Error 32-bit EL1 > ENDPROC(__hyp_stub_vectors) > > > > > Finally, if you can change the firmware to install the EL2 vectors, > > you can also change it to enter the kernel at EL2. I suggest you do > > that instead. > > I agree with you, but needs to change customer‘s board, I will try to > discuess with customer. In both cases, you'll need to change your customer's firmware. It seems to me that there is no reason for the arm64 boot protocol to change and adopt weird, wonderful and proprietary privilege escalation methods. Thanks, M. -- Without deviation from the norm, progress is not possible.

4 years, 5 months

1
0
0 0

2025

2024

2023

2022

2021

2020

2019

2018

TF-A